Receiving SMS and routing to an email - Revision history

Admin at 08:54, 16 October 2016

2016-10-16T08:54:20Z

← Older revision		Revision as of 08:54, 16 October 2016
Line 17:		Line 17:
	[[file:didsipmessage.png\|400px]]		[[file:didsipmessage.png\|400px]]

	== ~~Generic~~ API ==		== Custom API ==

	In your ~~DID~~, configure the URL https://.../pbx/receivesms.php		In your SMS Provider, configure the URL https://.../pbx/receivesms.php

	[[file:twilioincomingdid.png\|400px]]		[[file:twilioincomingdid.png\|400px]]

	So when your provider needs to deliver you a SMS, it will call your URL and provide all data.		So when your provider needs to deliver you a SMS, it will call your URL and provide all data.

			In your DID you need to configure which fields are mapped with each info:

			[[file:didscustoapi.png\|400px]]

			If you provider is twilio, you can use their protocol, in this case the fields are already mapped and there is no other need.

			[[file:didstwilio.png\|400px]]

Admin at 08:50, 16 October 2016

2016-10-16T08:50:17Z

← Older revision		Revision as of 08:50, 16 October 2016
Line 13:		Line 13:
	Add if not, then add this to the [general] section of sip.conf and reload the sip module		Add if not, then add this to the [general] section of sip.conf and reload the sip module

	~~== API ==~~		In your DID, configure the protocol SIP MESSAGE and its destinations

	In your ~~Provider~~, configure the URL https://.../pbx/receivesms.php		[[file:didsipmessage.png\|400px]]

			== Generic API ==

			In your DID, configure the URL https://.../pbx/receivesms.php

	[[file:twilioincomingdid.png\|400px]]		[[file:twilioincomingdid.png\|400px]]

			So when your provider needs to deliver you a SMS, it will call your URL and provide all data.

Admin at 08:27, 16 October 2016

2016-10-16T08:27:35Z

← Older revision		Revision as of 08:27, 16 October 2016
Line 11:		Line 11:
	</pre>		</pre>

	Add if not, then reload the sip module		Add if not, then add this to the [general] section of sip.conf and reload the sip module

	== API ==		== API ==

Admin: /* SIP MESSAGE */

2016-10-16T07:34:23Z

SIP MESSAGE

← Older revision		Revision as of 07:34, 16 October 2016
Line 11:		Line 11:
	</pre>		</pre>

	Add if not ~~and~~ reload sip module		Add if not, then reload the sip module

	== API ==		== API ==

Admin: /* API */

2016-09-30T20:42:49Z

API

← Older revision		Revision as of 20:42, 30 September 2016
Line 17:		Line 17:
	In your Provider, configure the URL https://.../pbx/receivesms.php		In your Provider, configure the URL https://.../pbx/receivesms.php

	[[twilioincomingdid.png\|400px]]		[[file:twilioincomingdid.png\|400px]]

Admin at 20:42, 30 September 2016

2016-09-30T20:42:28Z

← Older revision		Revision as of 20:42, 30 September 2016
Line 1:		Line 1:
	There are two ways to receive SMS. You can receive them as SIP MESSAGE or you can ~~pull~~ from your provider using an API.		There are two ways to receive SMS. You can receive them as SIP MESSAGE, or you can have them delivered from your provider using an API.

	== SIP MESSAGE ==		== SIP MESSAGE ==
Line 12:		Line 12:

	Add if not and reload sip module		Add if not and reload sip module

			== API ==

			In your Provider, configure the URL https://.../pbx/receivesms.php

			[[twilioincomingdid.png\|400px]]

Admin: Created page with "There are two ways to receive SMS. You can receive them as SIP MESSAGE or you can pull from your provider using an API. == SIP MESSAGE == As first step, please check if you..."

2016-09-30T18:21:12Z

Created page with "There are two ways to receive SMS. You can receive them as SIP MESSAGE or you can pull from your provider using an API. == SIP MESSAGE == As first step, please check if you..."

New page

There are two ways to receive SMS. You can receive them as SIP MESSAGE or you can pull from your provider using an API.

== SIP MESSAGE ==

As first step, please check if your system can receive messages using SIP protocol. In sip.conf check if you have the following rows:

<pre>
accept_outofcall_message=yes
outofcall_message_context=astsms
auth_message_requests = yes
</pre>

Add if not and reload sip module